This specification covers factory made PTFE lined metal pipe, fittings & valve primarily intended for conveying corrosive fluids.
All the technical specifications of our PTFE / PFA / FEP lined piping systemS generally exceeds the relevant ASTM F 1545-95 Standard specifications. This specification covers ANSI 150# PTFE lined pipe & fittings in nominal diameter from 25NB to 300NB.
Marerial of Construction: CS PTFE / PFA / FEP lined
Pipe & Fittings material : ASTM A106 Gr.B, in compliance with ANSI B 36.10. According to schedule 40 from 25NB to 150NB, schedule 30 from 200NB to 250NB & schedule 20 for 300NB.
Flange material: IS 2062 Gr.B ANSI B 16.5, ASA 150# for drilled holes
Valve body material: WCB casting as per lS-1 030
SS304 casting as per ASTM A351 gradeCF8
SS316 casting as per ASTM A351 gradeCF8M
PTFE liner for pipes: Isostatically molded liner with even pressure throughout the length, molded from standard resin as per ASTM D 1457, white color.
Lined fittings: Fittings are insitu molded in PTFE by isostatic molding process molded from standard resin as per ASTM D1457.
Lined Valves: Valves are lined with PTFE / PFA / FEP
Lining material- Resin Type
Standard Resin Specification Standar LinerColor
PTFE Polytetrafluoroethylene ASTMD1457 White
PFA Perfluoro [Alkoxyalkane] copolymer ASTM D 3307 Natural
FEP Perfluoro [Ethylene-Propylene] copolymer ASTM D 2116 Green
Lining Thickness: 3 to 8 mm from 25NB upto 300NB depends on size & location
Standard for Pipe: Collared ends with backing flange as per ANSI B16.5 ASA 150#, one end loose flange and other end fixed flange.
Standard for fittings: All fittings are with fixed welded flanges, loose flanges can be offered on extra cost.
Vents holes: Each pipe having two vent holes that will release any pressure between the liner and the housings.
Tolerance for pipe lingth : + 3.2 mm
Tolerance for flange bolt hole : + 1.6 mm
Inspection and testing : Pipes and fittings are tested with a non destructive high voltage tester at an output voltage of 10KV and hydrostatic pressure test at 10 Kg/cm2, ball valves are tested at air pressure of 2Kg/cm 2
Pressure rating: Vacuume to 6 kg/cm 2
Temperature rating: - 29°C to 260°C
External finish : Pipes and fittings are paint externally by red oxide primer and valves are paint externally with two coats of paint
Bore size (ID), flare diameter and flange thickness:
Size |
Lined pipe ID |
Flare Diameter |
Flange Thickness |
NB |
mm |
As per ASTM F1545-95 |
without RF mm |
25 |
18 |
47.6 |
14.5 |
40 |
32 |
68.3 |
14.5 |
50 |
42 |
87.3 |
16.5 |
80 |
67 |
117.5 |
18.5 |
100 |
88 |
150.8 |
18.5 |
150 |
138 |
203.2 |
23 |
200 |
186 |
255.6 |
23 |
250 |
234 |
311.2 |
25 |
300 |
282 |
365.1 |
33.6 |
Packing : Both ends of pipe are packed with good quality ply tightened with set of nut and bolts, fittings are packed with corrugated paper packing.
|